Fujitsu Error Code 71, Discharge Sensor Fault

Right where hot gas leaves the compressor, a small sensor keeps watch over the hardest working part of your system.

Fujitsu error code 71 tells you the outdoor board no longer trusts what that sensor reports. Because the reading protects the compressor, the system stops until the fault is fixed. Here is a practical guide to the sensor, the usual causes of failure and the repair.

What does Fujitsu error code 71 mean?

Fujitsu service information generally lists code 71 as a discharge temperature sensor error. The sensor is a thermistor clipped or strapped to the discharge pipe, the copper line carrying hot, high pressure gas out of the compressor. The outdoor board reads its resistance and works out the temperature.

When the reading jumps outside a believable range, the board decides the sensor circuit has failed. It then stops the compressor and reports code 71. Without that reading, the board cannot tell whether the compressor is overheating, so continuing to run would be risky.

Code 71 versus code A1

These two codes are easy to confuse, so it helps to compare them.

  • Code 71 means the sensor circuit itself seems faulty. The reading makes no sense, so the board cannot trust it.
  • Code A1 means the sensor works, but it reports a genuinely high temperature, so the system is protecting the compressor.

In other words, code 71 is about the measuring device, while A1 is about what it measures. A technician confirms which situation applies before deciding on a repair.

Why the discharge reading matters

Discharge temperature is one of the clearest windows into compressor health. It rises when the refrigerant charge drops, when airflow over the outdoor coil falls or when the compressor works under strain. The board uses this reading to slow the compressor, adjust refrigerant flow through the expansion valve and stop the system before temperatures reach damaging levels.

Without a trustworthy discharge reading, all of that protection disappears. That is why the system refuses to run with code 71 present, even though the compressor itself may be perfectly healthy.

Where the sensor lives

The discharge pipe sits inside the outdoor unit, close to the compressor. It runs very hot during operation, often far hotter than any other pipe in the system. The sensor clips onto this pipe, usually under a layer of insulation that helps it read the pipe temperature rather than the surrounding air. Its wire then runs through the compressor compartment to the outdoor board.

This location is demanding. The sensor faces high heat, constant vibration from the compressor and moisture from the outside environment.

Common causes of code 71

Heat damage to the wire

The wire runs near very hot pipes. If it touches the discharge pipe or compressor shell directly, the insulation can soften, crack or melt over time, leading to a short or open circuit.

Vibration and chafing

Compressor vibration can rub the wire against sharp metal edges, gradually wearing through the insulation.

Sensor slipping off the pipe

The clip or strap can loosen, letting the sensor move away from the pipe. The reading then becomes unrealistic, which can trigger code 71 or confuse the protection logic.

Moisture and corrosion

Rain, condensation and coastal salt can corrode the plug or work into the sensor body.

Failed thermistor

Repeated extreme heating and cooling eventually wears out the sensor element.

Board input fault

Occasionally, the circuit on the outdoor board that reads the sensor fails.

Rodent damage

Rats and mice sometimes shelter inside outdoor units and chew wiring, including sensor leads.

Safe checks you can do

Because the sensor sits inside the outdoor unit near high voltage parts, there is little you can safely check.

  1. Switch the system off with the remote.
  2. Turn off the isolator near the outdoor unit and the circuit at the switchboard.
  3. Wait several minutes, restore power and try once more.
  4. If the code returns, leave the system off.
  5. From outside the unit, look for signs of rodents, such as droppings or chewed material nearby.

Our guide on how to reset a Fujitsu air conditioner explains the restart steps.

Hot pipes and high voltage

The discharge pipe can reach temperatures that burn skin, and the compressor compartment holds high voltage. Please do not remove outdoor unit panels or touch internal pipes. Leave all inspection to a technician.

How a technician diagnoses code 71

Confirming the code

The technician confirms the code and checks for related codes, such as A1, A3 or outdoor sensor faults.

Inspecting the sensor and wire

With power isolated, they open the outdoor unit and inspect the sensor, its clip, the insulation and the full length of the wire. Heat damage, chafing and rodent bites are common findings.

Measuring resistance

They unplug the sensor and measure its resistance, comparing it with the expected value for the pipe temperature using the service information for your model. Because the pipe cools quickly once the system stops, they account for the actual temperature at the time of testing.

Testing the board input

If the sensor and wire test fine, they check whether the board reads a known good sensor correctly.

How the board uses discharge temperature day to day

Discharge temperature is not just a safety limit. On many inverter systems, the outdoor board uses the reading constantly to fine tune how the system runs. For example, it may adjust the electronic expansion valve to keep discharge temperature within a target band. Opening the valve slightly lets more refrigerant through, which cools the discharge gas. Closing it reduces flow, which raises the temperature.

This fine control helps the system run efficiently across a wide range of conditions, from mild spring days to scorching summer afternoons. It also explains why a faulty discharge sensor can cause odd behaviour even before code 71 appears. A sensor that reads slightly wrong can push the valve to the wrong position, which may lead to weak cooling, frost on pipes or higher running costs.

Intermittent code 71

Some owners see code 71 only occasionally. The system may run for days, then stop with the code, often during hot weather or after the compressor has run for a long time. Intermittent faults like this often point to a wire that only breaks contact when it expands with heat, or a plug that loosens with vibration.

Because the fault comes and goes, a short log helps. Write down when it appears, the weather at the time, how long the system had been running and whether cooling or heating was in use. This record gives the technician valuable clues, especially if the fault does not show up during the visit.

The insulation around the sensor

The sensor usually sits under a layer of insulation or a protective sleeve. That covering does two jobs. First, it helps the sensor read the pipe temperature accurately rather than the air around it. Second, it protects the sensor and its wire from direct contact with the hottest metal.

Over years, that insulation can harden, crack or slip. Once it does, the sensor may read inaccurately and the wire may sit closer to hot surfaces. Replacing damaged insulation during the repair is a small step that improves accuracy and helps the new sensor last much longer.

Signs worth mentioning when booking

Several observations help the technician prepare. Mention whether cooling or heating weakened before the code appeared, since that might suggest a separate refrigerant problem. Note whether the outdoor unit sounded different, perhaps louder or more strained. Mention any recent work near the outdoor unit, such as landscaping, painting or pest treatment, which might have disturbed wiring.

Comfort while the system is down

With code 71 active, the compressor will not run, so the system cannot cool or heat. Leave it switched off rather than forcing repeated restarts. On hot days, keep blinds closed, use fans and stay in the coolest part of the home during the afternoon. On cold days, close doors to unused rooms and keep curtains drawn after sunset to hold in warmth.

How long the repair usually takes

A discharge sensor repair is often completed in a single visit once the technician has the correct sensor for your model. Rerouting a damaged wire or replacing insulation adds a little time. If testing reveals a second problem, such as a refrigerant leak, the technician explains it and outlines the extra work before proceeding. Sharing the outdoor unit model number when booking helps the technician bring the right part.

A small part with a big role

It is easy to overlook a small sensor no bigger than the tip of a finger, yet the discharge sensor protects the most valuable component in your system. Fixing it promptly, and then confirming the compressor runs within a healthy range afterwards, is one of the very best ways to protect your investment and keep the whole system running reliably for many years.

Typical repairs

  • Refitting a loose sensor and replacing its clip or insulation.
  • Repairing or rerouting a heat damaged or chafed wire.
  • Cleaning or replacing a corroded plug.
  • Replacing the discharge temperature sensor.
  • Replacing the outdoor board in the rare case its input has failed.

Why routing the wire correctly matters

A replacement sensor will only last if its wire stays clear of hot surfaces and sharp edges. When fitting a new sensor, a careful technician routes the wire along its intended path, secures it with suitable ties and keeps it away from the compressor shell and discharge pipe. That attention to detail prevents the new sensor from failing in the same way as the old one.

Checking the system after the repair

Once the sensor is fixed, the technician runs the system and watches the discharge reading as the compressor warms up. A sensible, steadily rising reading confirms the sensor works. At the same time, it reveals whether the compressor runs at a healthy temperature. If the reading climbs too high, the technician investigates further, since a hidden refrigerant leak or airflow problem may also be present.

Rodents and outdoor units

Outdoor units offer warmth and shelter, so rodents sometimes move in, particularly in cooler months. They can chew sensor wires, power cables and insulation. If you notice droppings around the outdoor unit or hear scratching, mention it when booking. After the repair, reducing food sources and clutter around the unit helps discourage a return.

Keeping outdoor sensors healthy

  • Keep the area around the outdoor unit clear and tidy.
  • Book regular servicing so a technician can inspect internal wiring.
  • Address pest activity near the unit promptly.
  • In coastal homes, ask about corrosion checks during servicing.

Our service page explains what a professional service includes and how often to book one.

Fujitsu outdoor units carry several sensors, each with its own code. Error code 73 covers the outdoor coil sensor, while error code 74 covers the outdoor air temperature sensor. Code A3 relates to compressor temperature protection. Our Fujitsu error codes list explains how they fit together.

Fujitsu error code 71, booking a repair

If a restart does not clear Fujitsu error code 71, the discharge sensor circuit needs inspection. When booking, mention when the code started, whether you have noticed rodents and whether cooling or heating had weakened beforehand.

Call 02 9071 1142 or use our booking page to arrange a visit. A technician will repair the sensor circuit properly, check the wiring route and then confirm your compressor runs at a safe, healthy temperature in every mode.

Frequently asked questions

What does Fujitsu error code 71 mean?

It generally points to a discharge temperature sensor fault, where the board cannot trust the reading.

How is code 71 different from code A1?

Code 71 means the sensor circuit seems faulty, while A1 means the sensor reports a genuinely high temperature.

Can heat damage the sensor wire?

Yes. If the wire touches the hot discharge pipe or compressor, the insulation can fail over time.

Can rodents cause code 71?

Yes. Rodents sheltering in outdoor units sometimes chew sensor wires.

Is it safe to open the outdoor unit?

No. Pipes can be very hot and the compartment holds high voltage. Leave it to a technician.

Is a discharge sensor repair usually simple?

Often it is, though the technician must confirm the cause and check the compressor afterwards.

{“@context”:”https://schema.org”,”@type”:”HVACBusiness”,”@id”:”https://fujitsu.sydneyaircare.com.au/#business”,”name”:”Sydney Air Care, Fujitsu Service”,”url”:”https://fujitsu.sydneyaircare.com.au/”,”description”:”Fujitsu air conditioner repair, service and troubleshooting across Sydney. Independent service provider, not affiliated with Fujitsu.”,”areaServed”:[{“@type”:”City”,”name”:”Sydney”},{“@type”:”State”,”name”:”New South Wales”}],”parentOrganization”:{“@type”:”Organization”,”name”:”Sydney Air Care”,”url”:”https://sydneyaircare.com.au/”},”telephone”:”+61 2 9071 1142″} {“@context”:”https://schema.org”,”@type”:”FAQPage”,”mainEntity”:[{“@type”:”Question”,”name”:”What does Fujitsu error code 71 mean?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”It generally points to a discharge temperature sensor fault, where the board cannot trust the reading.”}},{“@type”:”Question”,”name”:”How is code 71 different from code A1?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Code 71 means the sensor circuit seems faulty, while A1 means the sensor reports a genuinely high temperature.”}},{“@type”:”Question”,”name”:”Can heat damage the sensor wire?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Yes. If the wire touches the hot discharge pipe or compressor, the insulation can fail over time.”}},{“@type”:”Question”,”name”:”Can rodents cause code 71?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Yes. Rodents sheltering in outdoor units sometimes chew sensor wires.”}},{“@type”:”Question”,”name”:”Is it safe to open the outdoor unit?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”No. Pipes can be very hot and the compartment holds high voltage. Leave it to a technician.”}},{“@type”:”Question”,”name”:”Is a discharge sensor repair usually simple?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Often it is, though the technician must confirm the cause and check the compressor afterwards.”}}]}
Call 02 9071 1142