Fujitsu Blowing Warm Air in Cooling Mode, Explained

Switching on cooling and feeling warm air instead is confusing, especially when the system seemed fine yesterday.

When you notice a Fujitsu blowing warm air in cooling mode, the cause usually falls into one of three groups, a setting, an airflow problem or a fault that stops the outdoor unit doing its job. This guide helps you work out which group applies and what to do next.

Why warm air means the outdoor side is not working

The indoor unit always moves room air across its coil. In cooling, that coil should be cold, so the air leaving it feels cool. If the coil is not cold, the air comes out at room temperature or warmer. Because the coil only gets cold when the outdoor unit runs the compressor and the refrigerant circuit works properly, warm air nearly always means something is stopping the outdoor side from delivering cooling.

Keep that idea in mind as you work through the checks. Most causes come down to the outdoor unit not running, running but not cooling or the system being in the wrong mode.

Check the settings first

Mode

Confirm the remote shows cooling mode. Heating mode, obviously, blows warm air. Fan mode blows air at room temperature. In auto mode, the system may choose heating on a cool morning. Our guide to Fujitsu air conditioner modes explains each setting.

Set temperature

If the set temperature is higher than the room temperature, the system will not cool. Lower it below the current room temperature.

Multi head mode conflicts

On multi head systems, if one indoor unit is in heating and another in cooling, the outdoor unit can only follow one request. Rooms set to the other mode may blow air without cooling. Make sure every indoor unit uses the same mode.

Recent restarts

After switching on, inverter systems may take a few minutes to start the compressor and cool the coil. Give the system around five minutes before deciding it is not cooling.

Check airflow

Filters

Badly clogged filters can reduce cooling so much that the air feels barely cool. They can also cause the coil to freeze, after which airflow drops further. Our guide on how to clean Fujitsu air conditioner filters shows the steps.

Outdoor unit clearance

The outdoor unit must release heat to the outside air. Leaves, plants, stored items or covers trap that heat. On very hot days, a crowded unit may struggle enough to stop cooling. Clear the area by hand with the isolator off.

Is the outdoor unit running?

Step outside and listen. When cooling, the outdoor unit usually hums and its fan spins.

Outdoor unit silent

If the indoor unit blows air but the outdoor unit stays silent, check the switchboard for a tripped breaker and confirm the isolator near the outdoor unit is on. If power seems fine, a communication fault, board fault or protection stop may be preventing the outdoor unit from running. Our page on a Fujitsu outdoor unit not working covers this in detail.

Outdoor fan stopped, compressor humming

If you hear the compressor but the fan does not spin, the outdoor coil cannot release heat. The system may soon stop on a protection code. Our page on error code 97 covers outdoor fan motor faults.

Everything runs, but the air stays warm

If both the fan and the compressor seem to run yet the air stays warm, the refrigerant circuit may have a problem, such as a leak, a stuck reversing valve or an expansion valve fault.

Faults that need a technician

Low refrigerant

A leak reduces cooling gradually. Eventually, there may not be enough refrigerant to cool the coil at all. Our gas and regas page explains how leaks are found and repaired.

Reversing valve stuck

The reversing valve switches the system between cooling and heating. If it sticks in the heating position, the system blows warm air in cooling mode.

Compressor not starting

On older models, a failed capacitor can stop the compressor starting. On inverter models, inverter or compressor faults can do the same. Codes such as 63, 94 and 95 relate to these faults.

Protection stops

High temperature or pressure protection, shown by codes such as A1, can stop the compressor while the indoor fan keeps running, which leaves warm air coming out.

Sensor faults

A faulty room or coil sensor can make the system think the room is already cool or that the coil is at risk of freezing, so it stops cooling.

Leave the technical checks to a professional

Please do not open panels, test wiring or handle refrigerant pipes. If you smell burning or the breaker trips, switch off at the switchboard and call for help.

Warm air that comes and goes

Sometimes the air alternates between cool and warm. This pattern offers useful clues.

Cool for a while, then warm

If the system cools normally for a period, then starts blowing warm air, a protection stop is a strong suspect. The compressor runs until a temperature or pressure limit is reached, stops, and the indoor fan keeps moving room air. After a rest, the compressor may restart and cooling returns, only to stop again later. Dirty outdoor coils, a weak outdoor fan or a low refrigerant charge commonly drive this cycle, especially on hot afternoons.

Warm at start, then cool

On the other hand, if the air feels warm for the first few minutes and then turns cool, the system may simply be starting up. Inverter compressors ramp up gradually, and the coil takes a little time to cool. In addition, if the system was recently in heating mode, the coil may still hold warmth. This behaviour is normal.

Warm only on the hottest days

Warm air that appears only during heatwaves suggests the system reaches its limit when outdoor temperatures soar. A crowded or dirty outdoor unit, an undersized system or a marginal refrigerant charge can all contribute. A service before summer helps.

The role of the outdoor coil

The outdoor coil is where all the heat from your home finally leaves. In cooling, hot refrigerant flows through the coil while the fan pulls outside air across the fins. If that air cannot flow freely, or if the fins are coated with dust, salt or grime, the refrigerant stays hot. Pressure rises, efficiency drops and the system may stop on protection, leaving the indoor fan to blow warm air.

You can help by keeping the area around the outdoor unit clear and by booking regular coil cleaning. Never use a high pressure hose on the fins, because it can flatten them and push water into electrical parts. Our Fujitsu outdoor unit check explains safe care at home.

Older systems with capacitors

Many older Fujitsu systems, and some fixed speed models, use start and run capacitors to help the compressor and outdoor fan motor start. When a capacitor weakens, the compressor may hum without starting, or the fan may refuse to spin. In either case, the indoor unit keeps blowing room temperature air. Capacitors can hold a dangerous charge even when the power is off, so please never touch them. A technician tests and replaces them safely.

Power and breaker issues

The indoor and outdoor units sometimes draw power from different circuits, or the outdoor unit may have its own isolator. If the outdoor circuit trips while the indoor unit stays powered, the indoor fan may run while the outdoor unit sits idle. Check the switchboard for any tripped breaker labelled for the air conditioner, and check that the outdoor isolator is on. If a breaker trips again after resetting, leave it off and book a check, because repeated tripping signals an electrical fault.

Recently serviced or repaired systems

If warm air started soon after a service, repair or installation, mention it when booking. A service valve left partly closed, a disturbed wire or a sensor not refitted correctly can all cause cooling problems. Most of these issues are quick to correct once identified.

Keeping comfortable until the repair

While waiting, switch the system off rather than letting it blow warm air, which only adds to the heat in the room. Close blinds before the sun reaches the windows, use fans to keep air moving and keep internal doors shut so the coolest room stays cool. Drink plenty of water on hot days, and keep an eye on anyone vulnerable to heat.

Checking the air temperature yourself

A simple thermometer helps you describe the problem accurately. After the system has run in cooling for about fifteen minutes, hold the thermometer in the airflow just in front of the indoor unit outlet. Then measure the room air a little distance away. If the outlet reading is clearly lower, the system is cooling, though perhaps not enough for the room. If the two readings are almost the same, the system is not cooling at all. Sharing these figures when you book helps the technician prepare.

How the technician narrows it down

On a warm air call, the technician confirms the mode and settings, reads any codes and then checks whether the compressor and outdoor fan run. If either part is not running, they test power, capacitors where fitted, the outdoor board and the motors. If both run, they connect gauges to measure refrigerant pressures and check the reversing valve and expansion valve. They also inspect the outdoor coil and the space around it. Working through these steps in order means they find the actual cause rather than guessing, and you only pay for the repair your system needs.

Ducted systems blowing warm air

Ducted Fujitsu systems follow the same principles, yet the indoor fan coil sits in the roof space. If warm air comes from every outlet, the outdoor unit or refrigerant circuit is usually responsible. If warm air comes from only some outlets, ducts or zones may be the issue instead, such as a duct that has come loose and is drawing hot roof space air. Mention which rooms are affected when booking.

Preventing warm air problems

Many warm air complaints trace back to problems that build slowly. Regular servicing keeps coils clean, confirms the refrigerant charge is correct and catches weak parts before they fail. Clean filters, a clear outdoor unit and prompt attention to new noises or codes all help. Our service page explains what a service includes.

Sun, location and the outdoor unit

Outdoor units on west facing walls, rooftops or in small enclosed courtyards can sit in intense heat on summer afternoons. In these spots, the air entering the coil may already be much hotter than the general outdoor temperature, which makes it harder for the system to reject heat. Consequently, cooling may fade during the hottest hours even though the system works well in the morning. Shading the unit from above, without enclosing it, and keeping plenty of open space around it can make a noticeable difference. A technician can advise whether relocating the unit would help in your home.

Fujitsu blowing warm air, booking a repair

If your Fujitsu is still blowing warm air after checking settings, filters and the outdoor unit, book a technician. When booking, mention whether the outdoor unit runs, whether the fan spins, whether cooling faded gradually or stopped suddenly and any codes.

Call 02 9071 1142 or use our booking page to arrange a visit. A technician will find out why the outdoor side is not cooling and fix it properly.

Frequently asked questions

Why is my Fujitsu blowing warm air in cooling mode?

Usually because the outdoor unit is not running, is running but not cooling or the system is in the wrong mode.

How long should I wait after switching on?

Give the system about five minutes to start the compressor and cool the coil.

Can a dirty outdoor unit cause warm air?

Yes. If it cannot release heat, cooling drops and the system may stop on protection.

What if the outdoor fan is not spinning?

The coil cannot release heat, so cooling stops. Switch off and book a check.

Can low refrigerant cause warm air?

Yes. A leak reduces cooling gradually until the coil can no longer get cold.

Why does one room blow warm air on a multi head system?

Check that all indoor units use the same mode, as the outdoor unit can only follow one.

{“@context”:”https://schema.org”,”@type”:”HVACBusiness”,”@id”:”https://fujitsu.sydneyaircare.com.au/#business”,”name”:”Sydney Air Care, Fujitsu Service”,”url”:”https://fujitsu.sydneyaircare.com.au/”,”description”:”Fujitsu air conditioner repair, service and troubleshooting across Sydney. Independent service provider, not affiliated with Fujitsu.”,”areaServed”:[{“@type”:”City”,”name”:”Sydney”},{“@type”:”State”,”name”:”New South Wales”}],”parentOrganization”:{“@type”:”Organization”,”name”:”Sydney Air Care”,”url”:”https://sydneyaircare.com.au/”},”telephone”:”+61 2 9071 1142″} {“@context”:”https://schema.org”,”@type”:”FAQPage”,”mainEntity”:[{“@type”:”Question”,”name”:”Why is my Fujitsu blowing warm air in cooling mode?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Usually because the outdoor unit is not running, is running but not cooling or the system is in the wrong mode.”}},{“@type”:”Question”,”name”:”How long should I wait after switching on?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Give the system about five minutes to start the compressor and cool the coil.”}},{“@type”:”Question”,”name”:”Can a dirty outdoor unit cause warm air?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Yes. If it cannot release heat, cooling drops and the system may stop on protection.”}},{“@type”:”Question”,”name”:”What if the outdoor fan is not spinning?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”The coil cannot release heat, so cooling stops. Switch off and book a check.”}},{“@type”:”Question”,”name”:”Can low refrigerant cause warm air?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Yes. A leak reduces cooling gradually until the coil can no longer get cold.”}},{“@type”:”Question”,”name”:”Why does one room blow warm air on a multi head system?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Check that all indoor units use the same mode, as the outdoor unit can only follow one.”}}]}
Call 02 9071 1142