Fujitsu Air Conditioner Not Turning On, Step by Step Checks
Pressing the remote and getting no response at all is unsettling, particularly on the first hot day of summer.
A Fujitsu air conditioner not turning on often has a simple explanation, such as flat remote batteries or a switch someone turned off. Working through the checks below in order will either solve the problem or give a technician the information they need to fix it quickly.
Begin with the remote
Batteries
Flat or weak batteries are the most common reason a system seems dead. If the remote display is blank, faint or flickering, replace both batteries with fresh ones.
Signal
The remote uses infrared light, so it needs a clear line of sight to the receiver on the indoor unit. Stand directly in front of the unit, a few metres away, and try again. Bright sunlight, some LED lights and obstacles can interfere with the signal.
Testing the remote
Point the remote at a phone camera and press a button. Many phone cameras show a flicker of light from the remote tip. If you see nothing, the remote may be faulty. Our page on a Fujitsu remote not working explains more checks.
Wall controllers
Ducted systems and some splits use a wired wall controller. If its display is blank, the indoor unit may have lost power, or the controller or its cable may have a fault.
Check the power
Circuit breaker
Look at the switchboard for a tripped breaker labelled for the air conditioner. If it has tripped, switch it back on once. If it trips again, leave it off and book a technician, because repeated tripping signals an electrical fault.
Isolator switch
Most outdoor units have an isolator switch nearby. Someone may have switched it off during gardening, painting or maintenance. Make sure it is on.
Power outage effects
After an outage, some systems need a moment to reset, while others remain off until you press the remote. If clocks around the home are flashing, power was interrupted recently.
Safety switch
If the safety switch at the switchboard trips when the air conditioner tries to start, there may be a fault such as moisture in electrical parts or damaged wiring. Leave it off and book a check.
Use the manual button
Many Fujitsu indoor units have a manual or emergency operation button, usually under the front panel or on the side of the unit. Pressing it starts the system without the remote. If the system starts this way, the remote or its receiver is likely at fault. If it still does nothing, the problem lies with power or the unit itself. Check your owner manual for the button location on your model.
Look for lights and codes
Even if the system does not start, the indoor unit may display lights or flash a pattern. A flashing lamp pattern usually signals a fault code. Note the pattern and look it up in our Fujitsu error codes list. Our guide on how to check Fujitsu error codes explains how to read them.
Common causes when the basics check out
Communication faults
If the indoor unit powers up but the outdoor unit never responds, a communication fault between them may stop the system. Our page on error code 11 explains this fault.
Blown fuse
Indoor and outdoor boards often include fuses. A power surge or fault can blow one, leaving the system dead. Before replacing it, a technician needs to find out why it blew.
Board failure
A failed indoor board can leave the unit completely unresponsive. Our page on error code 32 explains indoor board faults.
Receiver fault
The small receiver that picks up remote signals can fail, leaving the unit unable to hear commands even though it has power.
Wiring damage
Rodents, renovations and weather can damage the cable between the indoor and outdoor units or the supply cable.
Indoor and outdoor units contain mains voltage. Please do not remove covers, check fuses or test wiring. If a breaker or safety switch keeps tripping, leave it off and call a technician.
What different symptoms suggest
The exact behaviour of a system that will not start tells you a lot. Matching your situation to one of these patterns helps you decide what to do next.
Completely dead, no lights, no beep
When nothing at all happens, power is the main suspect. A tripped breaker, an isolator turned off, a blown fuse inside the unit or a damaged supply cable can all leave the indoor unit dead. Remote batteries are worth checking too, although a completely dead indoor unit usually shows no lights even when you press the manual button.
Beeps but does not start
If the indoor unit beeps when you press the remote but nothing else happens, the unit is receiving commands. In that case, the problem may involve the outdoor unit, a communication fault or a protection lockout. Look for flashing lamps and note any pattern.
Lights flash, no operation
Flashing lamps usually mean the board detected a fault and refuses to run until it is cleared. The pattern identifies the fault, so note it carefully or record a short video.
Indoor fan runs, outdoor unit silent
If the indoor fan starts but the outdoor unit never joins in, the outdoor unit may lack power, have a fault or not be receiving signals. Our page on a Fujitsu outdoor unit not working covers this pattern.
Starts then stops straight away
A system that starts briefly and then stops may be hitting a protection limit or a fault immediately. Note how long it runs and whether a code appears. Our page on a Fujitsu air conditioner that turns off by itself explains related causes.
After storms and outages
Storms are one of the most common triggers for a system that suddenly will not start. Power surges can trip breakers, blow fuses on circuit boards or damage electronics. Sometimes, the system simply needs a full power reset.
To reset safely, switch the system off at the remote, then turn off the isolator and the air conditioner breaker. Wait several minutes, switch the power back on and try the remote again. Our guide on how to reset a Fujitsu air conditioner explains the process. If the system still does not start, or a breaker trips, surge damage is possible and a technician should check it.
Systems unused for months
Systems left unused through a season sometimes refuse to start when needed again. Flat remote batteries, an isolator switched off during the off season, insects nesting inside units or moisture in electrical parts can all play a part. Before the season starts, test the system on a mild day so you have time to arrange a repair before you really need it.
Ducted system checks
For ducted Fujitsu systems, start with the wall controller. A blank controller suggests the indoor fan coil has no power, often because of a tripped breaker or a switch near the fan coil. Some ducted installations include a separate isolator in the roof space near the fan coil, though you should not climb into the roof to check it. Where the controller shows a code, note it. If the controller shows normal settings but nothing happens, a communication or board fault may be involved.
Pests inside the unit
Insects and small animals cause more start up failures than most people expect. Ants are attracted to warm electrical compartments and can pack into relays and connectors, causing shorts or open circuits. Cockroaches shelter in indoor units, especially in kitchens and apartments. Geckos and rodents sometimes climb into outdoor units, where they can damage wiring or get caught in electrical parts. If you have noticed pests around the indoor or outdoor unit, mention it when booking, as it changes what the technician looks for first.
Wifi controlled systems
If your system connects to wifi, an app command, a schedule or a lost connection can make it seem as though the system will not start. Try the handheld remote or wall controller directly. If the system responds to the remote but not the app, the problem lies with the wifi adaptor or app rather than the air conditioner. Our guide to Fujitsu wifi setup explains how to troubleshoot app connections.
Recently installed systems
A new system that will not start may have a wiring issue, an incorrect setting or a missing step from commissioning. Contact the installer first, as the work is likely under their warranty. Keep the installation invoice and any paperwork they provided.
When to call straight away
Some situations call for an immediate call rather than more troubleshooting. A burning smell, scorch marks near the isolator or power point, a safety switch that trips every time or water near electrical fittings all need a professional. Switch off at the switchboard and leave the system alone until a technician checks it.
Information that helps us help you
When you call, describe exactly what happens when you press the remote or the manual button. Mention whether any lights appear, whether the unit beeps and whether the outdoor unit makes any sound. Note whether a breaker or safety switch tripped and whether there was a storm, outage or building work beforehand. Share the model number from the rating label if you can find it. These details help the technician arrive with the right parts and test equipment, which often means the repair can be completed in one visit.
A photo of any flashing lamps or controller display also helps confirm the fault quickly.
How a technician diagnoses a dead system
When a system will not start, the technician works methodically from the supply inward. First, they confirm power at the switchboard, the isolator and the terminals on the indoor and outdoor units. Next, they check fuses on the boards and look for signs of surge damage, water entry or pests. Then they test the communication cable between the units and the receiver that picks up remote signals. Finally, they test the indoor and outdoor boards. Once they find the fault, they explain the repair and its cost before going ahead.
Typical repairs
- Resetting or repairing a faulty breaker or safety switch circuit, with an electrician where needed.
- Replacing a blown fuse after correcting what caused it.
- Repairing damaged supply or interconnecting cables.
- Replacing a faulty receiver or remote.
- Replacing a failed indoor or outdoor board.
Comfort until the repair
While you wait, use fans, blinds and closed doors in hot weather, or extra layers and closed off rooms in cold weather. If someone in the home is vulnerable to heat or cold, mention it when booking so we can understand the urgency.
Preventing start up problems
Test your system before each season, keep spare remote batteries on hand, leave the isolator switched on unless maintenance requires otherwise and book regular servicing. Surge protection installed by an electrician can also help protect electronics during storms. Our service page explains what a service includes.
Fujitsu air conditioner not turning on, booking help
If your Fujitsu air conditioner is still not turning on after checking the remote, the power and the manual button, book a technician. When booking, mention what you have tried, whether any lights show and whether a breaker or safety switch tripped.
Call 02 9071 1142 or use our booking page to arrange a visit. A technician will find out exactly why the system will not start, fix the fault properly and get it running comfortably again.
Frequently asked questions
Why is my Fujitsu not turning on?
Flat remote batteries, a tripped breaker or an isolator switched off are the most common causes.
How do I test the remote?
Point it at a phone camera and press a button. Many cameras show a flicker of light if it works.
Is there a way to start the unit without the remote?
Many models have a manual operation button under the front panel. Check your owner manual.
What if the breaker keeps tripping?
Leave it off and book a technician, as repeated tripping signals an electrical fault.
Can a power outage stop the system restarting?
Some models stay off until you press the remote after power returns.
What if lights are flashing but it will not start?
A flashing pattern usually signals a fault code. Note it and book a check.